Home hub 3000 admin password

Keitlink
Contributor

The default admin passwd for Home hub 3000, after factory reset is supposed to be the modem serial, This does not work.

How can I find the admin password.

0 1 124
1 helpful reply

Accepted Solutions

WelshTerrier
Community All-Star
Community All-Star

Good Day & Welcome @Keitlink 

The current version of the Bell Home Hub 3000 admin password uses the default serial number printed on the white sticker on the back/side of the modem. If you changed it and lost the new one, you must perform a factory reset by holding the reset button for 30 seconds.

FYI only: After a factory reset, if the default serial number does not work, try entering: "admin" in place of the serial number. (On earlier versions of the Home Hub 3000 modem, "admin" was the default password.)

To factory reset your Home Hub 3000 modem:

  • Locate the small Reset button on the side of your modem.
  • Use a pin or paperclip to press and hold it for at least 30 seconds, until the power light flashes red 5 times.
  • Keep in mind that a factory reset will erase custom changes. 
  • You may also need to reenter your b1 username and password. If you know what they are then it is safe for you to do a factory reset.
  • How to reset my Home Hub 3000 modem to factory settings

As a side point, did you previously setup: "Password recovery" on your Hub 3000 when it was installed? If not, then you should do so to avoid a similar situation from reoccurring again.

To setup Password recovery:

  1. Open your web browser. > Enter the following in your address bar: 192.168.2.1
  2. Click on Modem preferences.
  3. If prompted, enter the administrator password. Unless you have changed it, the default password is the serial number located on the sticker on the back of the modem.
  4. In the Contact information section, enter your email address & confirm your Email address. Optionally, you can also add your mobile number to receive a text message.
  5. Click the Save button.
  6. Exit your web browser & press the Password recovery button on your modem.

If all else fails and you are still unable to access your Bell modem, you will need to contact Bell Internet Tech support for further assistance.

Take care.

I am a Community All-Star and customer. I'm here to help by sharing my knowledge and experience. My views on Bell and the Community Forum are my own and not the views of Bell or any of its affiliates.

View reply in original post

1 REPLY 1

WelshTerrier
Community All-Star
Community All-Star

Good Day & Welcome @Keitlink 

The current version of the Bell Home Hub 3000 admin password uses the default serial number printed on the white sticker on the back/side of the modem. If you changed it and lost the new one, you must perform a factory reset by holding the reset button for 30 seconds.

FYI only: After a factory reset, if the default serial number does not work, try entering: "admin" in place of the serial number. (On earlier versions of the Home Hub 3000 modem, "admin" was the default password.)

To factory reset your Home Hub 3000 modem:

  • Locate the small Reset button on the side of your modem.
  • Use a pin or paperclip to press and hold it for at least 30 seconds, until the power light flashes red 5 times.
  • Keep in mind that a factory reset will erase custom changes. 
  • You may also need to reenter your b1 username and password. If you know what they are then it is safe for you to do a factory reset.
  • How to reset my Home Hub 3000 modem to factory settings

As a side point, did you previously setup: "Password recovery" on your Hub 3000 when it was installed? If not, then you should do so to avoid a similar situation from reoccurring again.

To setup Password recovery:

  1. Open your web browser. > Enter the following in your address bar: 192.168.2.1
  2. Click on Modem preferences.
  3. If prompted, enter the administrator password. Unless you have changed it, the default password is the serial number located on the sticker on the back of the modem.
  4. In the Contact information section, enter your email address & confirm your Email address. Optionally, you can also add your mobile number to receive a text message.
  5. Click the Save button.
  6. Exit your web browser & press the Password recovery button on your modem.

If all else fails and you are still unable to access your Bell modem, you will need to contact Bell Internet Tech support for further assistance.

Take care.

I am a Community All-Star and customer. I'm here to help by sharing my knowledge and experience. My views on Bell and the Community Forum are my own and not the views of Bell or any of its affiliates.